Washer Won’t Fill With Water? Repair in Hattiesburg, MS

The cycle starts but the tub stays empty or fills slowly. Here is how to check the water supply and when the inlet valve is to blame.

Short answer

A washer that will not fill usually has closed or kinked supply hoses, a clogged inlet screen, a failed water inlet valve, a faulty lid switch or a pressure problem. Check that both taps are fully open, straighten the hoses and clean the inlet screens. If water still does not come in, the valve or switch likely needs replacing.

Why won’t my washer fill?

Water has to get to the washer, through the valve and into the tub, and the machine must think it is safe to start. A fault at any of those steps leaves the drum dry or slow.

White front-load washer with the top cover off, exposing the detergent dispenser and water hoses
Dispenser and fill hoses exposed.
CauseHow to spot itFix
Taps closed or hoses kinkedNo water or a trickle at the hoseOpen the taps fully; straighten the hoses
Clogged inlet screensSlow fill, low flow at the washerClean the screens at the hose ends
Failed water inlet valveHum or buzz, no water, or only hot or coldReplace the valve
Lid switch or door lockDoes not start filling; no clickReplace the switch or lock
Low water pressureSlow fill, other taps also weakCheck supply; call a plumber if needed

What should I check first?

  1. Make sure the hot and cold taps behind the washer are fully open.
  2. Look for kinked or crushed hoses and pull the washer out slightly if needed.
  3. Turn off the taps, unscrew the hoses and clean the small screens at the washer inlets.
  4. Turn the taps back on and check that water flows freely from each hose into a bucket.
  5. Close the lid or door firmly and start a cycle again.

If water flows from the hoses but the washer will not take it, the inlet valve or lid switch is the likely fault. That is a repair we do at your home.

Water supply around Hattiesburg

In town, supply pressure is usually fine. Outside the city, homes on wells have a pressure tank and pump that can wear out, and a washer fill that suddenly gets slow while other taps also slow down points to the well system, not the machine. Sediment and mineral flakes can also clog the little screens at the inlet, and older homes may have old galvanized plumbing with the same problem.

What does fill repair cost in Hattiesburg?

The service call is $75, and the price for any repair is written and agreed before we start. Inlet valves and lid switches are common, moderate repairs. See the cost guide for more.

How the washer controls filling

When you start a cycle, the control board opens the water inlet valve, which is an electrically operated gate at the back of the washer where the hoses connect. Water flows until a pressure switch or sensor tells the board the tub has reached the right level, and then the valve closes. A problem at any point in that chain can leave the washer dry, slow to fill or filling only with hot or only with cold.

Do the bucket test

Before blaming the washer, turn off both taps, unscrew a hose from the back of the washer and point it into a bucket. Turn the tap back on. A strong, steady stream means the house supply is fine, so the problem is inside the machine. A weak stream means the tap, the hose or the home’s supply is the problem. Repeat for the other hose. Be careful because the water can be hot.

What you seeLikely cause
Weak flow at the hose, strong at other tapsPartly closed tap or clogged hose screen
Strong flow at hoses, no water in the tubFailed inlet valve or lid switch
Fills only hot or only coldOne side of the dual inlet valve has failed
Fills slowly, humsValve screens clogged, or low house pressure
Fills, then says it has not filledPressure switch or sensor problem
Fills with the lid openNot safe: stop and call; lid switch fault

Why inlet valves fail

The valve contains a small electric coil and a fine screen. Over time, mineral particles clog the screen, and the coil can burn out or stick. Because washers shut off hard when the valve closes, a valve can also develop a leak at the hose connection. Replacing the valve is a routine repair, and we match the part to your exact model.

Well-water notes

If you live outside town on a private well, check the well pump and pressure tank first when fill speed drops in every faucet, not just the washer. Hose screens on the washer can also collect sediment after any well or main-line work, so cleaning them is a good first step after plumbing changes in your area.

Keep it from happening again

  • Replace rubber supply hoses every five years or sooner, or use braided stainless hoses.
  • Turn the taps off when you leave for a long trip.
  • Clean the inlet screens when you notice the fill slowing.

Related problems

If water comes in but does not leave, read washer won’t drain. If water comes in and keeps coming, see overflow problems.

FAQ

Washer won’t fill questions, answered

Why is my washer not filling with water?

Start with the taps and hoses. If water flows to the washer, the usual causes are a clogged inlet screen, a failed water inlet valve or a lid switch that will not let the cycle start.

Why does my washer fill so slowly?

Clogged inlet screens, kinked hoses or low supply pressure are the usual reasons. If other taps are also slow, the problem is in the house or well supply.

Can a washer fill with only hot or cold water?

Yes. The inlet valve has separate sides for hot and cold, and one can fail. The washer may still run but wash in the wrong temperature.

Should I replace the fill hoses?

Hoses age. Replace them every few years, and use braided hoses with a tight connection. Old rubber hoses can crack or burst.

Do you repair inlet valves in Hattiesburg?

Yes. We test the valve, replace it if it has failed and run a full fill cycle before we leave.

Washer won’t fill? We’ll get water flowing.

Call (601) 419-6599 for a written price before any work starts. 2624 Lincoln Rd, Hattiesburg, MS 39402. Monday to Saturday, 8 a.m. to 6 p.m. Request service for washer not filling with water today.