Washer Overflowing? Repair in Hattiesburg, MS
Water pouring over the top or out the front. Stop it first, then find the cause.
If your washer is overflowing, stop the cycle, unplug it and turn off both water taps. The usual causes are a stuck water inlet valve, a faulty water level switch or sensor, too many suds or a blocked drain that backs water up. Do not use the washer again until the cause is found.
What should I do right now?
- Turn off the washer, unplug it if you can reach the plug safely and turn off both water taps.
- Do not step in water near the plug. Switch off the breaker if the outlet is wet.
- Bail out or soak up the water and move rugs and laundry out of the way.
- Check whether the drain hose is still in the standpipe.
- Call us before you run another load.
Why does a washer overflow?
A washer should shut off the water when the tub reaches the right level. Overflow means water kept coming, or water could not leave.
| Cause | How to spot it | Fix |
|---|---|---|
| Stuck water inlet valve | Water keeps entering after the washer is off | Replace the valve |
| Faulty water level switch or sensor | Tub fills past the normal level | Replace the switch or sensor |
| Too many suds | Foam pushes out of the tub | Use less detergent; use HE detergent |
| Blocked drain or standpipe | Water rises in the standpipe and backs up | Clear the drain; see washer won’t drain |
| Drain hose pushed too far down | Siphoning or back flow | Reposition the hose with an air gap |
Overflow problems around Hattiesburg
With soft water, suds are the number one cause we see. A little too much detergent turns into foam that pours over the top, especially in front-loaders and HE washers. Older homes may also have standpipes that are partly blocked by years of lint. Check the leaking washer page if water appears from underneath instead of over the top.
What does overflow repair cost in Hattiesburg?
The service call is $75, and any repair is priced in writing before we begin. A stuck inlet valve or a level sensor is a common, moderate repair. Water damage to floors is a separate matter for your insurer or a plumber. See the cost guide.
Overflow versus leak
Water coming over the top or out of the detergent drawer is an overflow, and water seeping from underneath is a leak. They have different causes, so work out which one you have. This page covers overflow. If the water is coming from underneath or behind the washer, see washer leaking water.
First, stop the water
- Press Cancel or Pause. If water keeps coming in, turn off both supply taps behind the washer.
- Unplug the washer if water is near the outlet or the cord.
- Bail out standing water with a bucket and towels so it cannot soak into the subfloor.
What causes an overflow
| Cause | How it shows up |
|---|---|
| Water level sensor or pressure switch failure | Tub keeps filling past the normal level |
| Inlet valve stuck open | Water keeps flowing even when the washer is off |
| Too much detergent | Suds foam out of the drawer or lid |
| Clogged drain with fill continuing | Water rises because it cannot leave |
| Blocked or kinked sensor hose | Control senses the tub as empty |
Two telltale signs
If the water keeps flowing into the washer after you turn the machine off, the inlet valve is stuck open. That is a valve replacement, and until it is done you should leave the taps closed. If instead the drum is full of suds, the detergent is the issue. Let the suds settle, run a rinse and use much less detergent next time.
Why overflows are urgent
Water on a laundry room floor can get into the subfloor, the walls and the floor below, and warm humid conditions make mold start quickly. If the washer has overflowed even once, get the cause fixed before using it again, and dry the area well. A technician can test the water level system and the inlet valve and tell you plainly what failed.
Prevent overflows
- Use the right amount of high-efficiency detergent.
- Turn the taps off when you leave home for several days.
- Keep the drain filter and hose clear.
What to do afterward
- Soak up all the water, and use a fan to dry the floor and baseboards.
- Check under and behind the washer for any damp spots.
- Leave the washer unplugged and the taps off until the cause is found.
- If the overflow reached walls or a lower floor, contact your insurer or a water-damage professional.
What the repair costs
The service call is $75, which covers the visit and the diagnosis. The price of any repair is written and agreed with you before we start, so there are no surprises. Parts and labor vary by washer and fault; our repair cost guide explains typical ranges.
Related problems
If the washer will not fill at all, read washer won’t fill. For water on the floor, see washer leaking water.
Washer overflowing questions, answered
Why is my washer overflowing?
A stuck water inlet valve, a faulty level sensor, too much detergent or a blocked drain are the usual causes.
What should I do first if my washer is flooding?
Turn off the washer and the water taps, unplug it only if the area is safe and mop up. Do not run the washer again until it is checked.
Can too much detergent make a washer overflow?
Yes. Foam can push out of the tub and look like a flood. Use HE detergent and less of it, especially in soft water.
Can a clogged drain make a washer overflow?
Yes. If water cannot leave the standpipe, it backs up and spills. Clear the standpipe and check the hose.
Do you fix overflowing washers in Hattiesburg?
Yes. We find the cause, replace the faulty valve or sensor and test the fill and drain before we leave.
Washer flooding? Call us.
Call (601) 419-6599 for a written price before any work starts. 2624 Lincoln Rd, Hattiesburg, MS 39402. Monday to Saturday, 8 a.m. to 6 p.m. Request service for washer overflowing today.