Top-Load Washer Repair in Hattiesburg, MS

Won’t spin, won’t agitate, banging or leaking. We repair top-loaders at your home with a written price first.

Short answer

We repair top-load washers in Hattiesburg and across the Pine Belt at your home. The most common faults are a failed lid switch, a worn motor coupling or clutch, a slipped belt and a clogged drain pump. The service call is $75, and you get a written price before we start work.

What goes wrong with top-load washers

Top-loaders are simpler than front-loaders, and most of their faults fall into a short list. Here is how we read the symptoms.

What you noticeUsual causeTypical fix
Fills and agitates but will not spinLid switch, motor coupling, clutch or drive beltTest the lid switch first, then the drive parts
Does nothing at allLid switch, control board or power supplyTest the switch and power, then the board
Water stays in the tubClogged pump or hose, or a failed drain pumpSee washer won’t drain
Loud banging, shaking or walkingOverloaded or off-balance load, worn suspension rods, or an unlevel machineLevel it, rebalance, replace suspension parts if worn
Leaks under the washerLoose hose, failed water pump or a leaking tub sealSee washer leaking water
Slow fill or no fillClosed taps, clogged inlet screens or a failed inlet valveClean the screens or replace the valve

Why won’t my top-load washer spin?

If it fills and agitates but the clothes come out soaking, start with the lid switch. The washer will not spin if it thinks the lid is open, and a worn or broken lid switch is one of the most common reasons. The part itself is cheap, and the repair is usually quick.

If the switch is fine, we look at the drive. On many Whirlpool, Kenmore and Maytag direct-drive top-loaders, agitating without spinning is the classic sign of a worn motor coupling. On belt-driven models, a worn or slipped belt does the same thing. Clutches wear out too, and you may notice a burning smell or slow spin first.

What can I check before I call?

  • Close the lid firmly and listen for a click. No click can mean a broken lid switch or strike.
  • Take out some of the load. Overstuffed tubs often will not spin.
  • Make sure the washer sits level and all four feet touch the floor.
  • Run a drain-and-spin cycle with no clothes. If it spins empty but not loaded, tell us.

Top-load washers do not have a door boot

Many people search for a door seal on a top-loader. There isn’t one. If a top-load washer leaks, the cause is usually a hose connection, the water pump or the tub seal, not a gasket. That is also why a puddle under a top-loader needs a proper look and not a guess.

HE top-loaders and agitator washers

HE top-loaders without a center agitator use less water, so too much detergent causes suds and slow drains quickly. In Hattiesburg’s soft water, measure your detergent and use HE soap. Traditional agitator washers are tougher, but they have more moving parts under the tub, so couplings and clutches wear.

What top-load washer repair costs in Hattiesburg

The service call is $75. After we diagnose, you get a written price. A lid switch or lock is usually on the lower end, around $150 to $250. Belts, hoses and couplings run roughly $120 to $325 depending on the parts. See the full repair cost breakdown.

Old top-loaders in older Hattiesburg homes

We see a lot of long-lived top-loaders in the older homes around Midtown, Oak Grove and downtown, and in rentals near USM. Many are worth fixing if the tub and transmission are sound. We check the bigger parts first, tell you what we find and let you decide whether a repair makes sense against the washer’s age.

A real top-load repair: the washer that walked across the floor

A Hattiesburg homeowner called us because their top-load washer had started banging during the spin cycle and was moving across the laundry room at higher speeds. They assumed it was at the end of its life, but wanted a professional opinion before buying a new one.

Our technician checked whether the washer was level, then examined the suspension system, the drum movement and the internal components. The problem was in the suspension, which was letting the tub move too much at spin speed. After explaining the findings, we replaced the faulty component, rechecked the balance and leveling, secured the washer in position and ran a spin test. The noise and vibration dropped sharply, and the customer kept the washer. Takeaway: a banging washer is worth a look early, before the movement damages something else.

Why does a top-load washer bang or walk during spin?

The four usual reasons, in order of how often we see them: an unbalanced load, an unlevel floor, worn suspension rods and, less often, a worn drive component. Older Hattiesburg homes with wood floors and pier foundations flex, so a heavy spin can make even a healthy washer shake. Level all four feet first. If it still walks, call us. See the cost page for suspension repair ranges.

Other top-load faults we see

Where we repair top-loaders

Across Hattiesburg and the Pine Belt, including Petal, Purvis, Sumrall, Lumberton and Laurel. The full list is on our areas we serve page. Questions before you call? Try the FAQ or contact us.

What customers say

Experienced and friendly technician

“My washing machine was making unusual noises and vibrating heavily during the spin cycle. I thought I might need to replace it, but the technician carefully checked the machine and identified the actual problem. He explained everything in simple terms and completed the repair efficiently. I also appreciated how respectful and friendly he was. My washing machine is running smoothly again. Highly recommended!”

FAQ

Top-load washer repair questions, answered

Why does my top-load washer fill and agitate but not spin?

The lid switch is the first thing to check. If it fails, the washer may agitate but will not spin. After that come the motor coupling, clutch or drive belt, depending on the model. We test in that order so you do not pay for parts you don’t need.

How much does a lid switch repair cost?

The part is inexpensive. With the service call and labor, most lid switch or lock repairs in Hattiesburg run about $150 to $250. You get a written price before we start work.

Can you fix an HE top-load washer without an agitator?

Yes. We repair HE and traditional agitator top-loaders from Whirlpool, Maytag, Kenmore, GE, LG, Samsung and others. Give us the brand and model number when you call.

Why is my top-load washer so loud when it spins?

Loud banging usually means an unbalanced load, an unlevel washer or worn suspension rods. Grinding or squealing points to a worn clutch, belt or bearing. Try rebalancing the load first, and call us if it keeps happening.

Is a 10-year-old top-load washer worth repairing?

It depends on the fault. A lid switch or belt on a washer in good shape is almost always worth fixing. A failed transmission or a rusted tub on an old machine often is not. We will compare the cost to a new washer and tell you honestly.

Do you repair washers for landlords?

Yes. We work with property managers and landlords, and we can send the written estimate to the owner for approval before the work starts.

Top-loader not spinning? Let’s get it going.

Call (601) 419-6599 for a written price before any work starts. 2624 Lincoln Rd, Hattiesburg, MS 39402. Monday to Saturday, 8 a.m. to 6 p.m. Request service for top load washer repair Hattiesburg today.