Washer Shaking and Walking? Repair in Hattiesburg, MS

The washer rocks, vibrates or crawls across the floor on the spin. Some causes are free to fix, and some need a technician.

Short answer

A washer that shakes or walks is usually unlevel, overloaded or unbalanced. Level all four feet, wash bulky items separately and keep loads even. If it still shakes, the suspension, shock absorbers or drum support may be worn, and a technician can replace them. Shipping bolts left in a new washer also cause violent shaking.

Why does my washer shake and walk?

During the spin, the drum can reach hundreds of rotations a minute. Anything out of balance multiplies. The washer shakes because the floor, the load or the suspension is not holding the drum steady.

Front-load washer with the side panel removed, showing the tub housing and balance weights
Checking the tub and balance weights.
CauseHow to spot itFix
Unlevel washerRocks when you push a top cornerAdjust the feet and tighten the lock nuts
Unbalanced or overloaded drumViolent shake only with heavy loadsSpread the load; wash bulky items alone
Soft or uneven floorShakes even when level; floor flexesMove the washer or reinforce the floor
Worn suspension or shock absorbersBangs and shakes on every spinReplace the worn parts
Shipping bolts still in a new washerViolent shaking from day oneRemove the transit bolts

What should I check first?

  1. Push down on each top corner. If it rocks, adjust the feet until all four are firm.
  2. Tighten the lock nuts against the base after leveling.
  3. Take out half the load and run a spin. If the shaking stops, the load was the problem.
  4. Look at the floor. A spongy section can make a level washer shake.
  5. On a new front-loader, check that the shipping bolts were removed.

If it still shakes with a small load on a level floor, the suspension or shock absorbers are likely worn. That is a repair we do at your home.

Floors and washers around Hattiesburg

Older homes and pier-and-beam houses in the Pine Belt can have floors that flex, and a washer on an upper floor or an enclosed porch amplifies every wobble. Rentals near USM sometimes have washers sitting on worn vinyl over uneven slabs. Leveling feet and a solid base matter more here than most people expect.

A shaking washer we repaired

A top-load washer in Hattiesburg was banging and creeping across the floor during the spin. The owner thought it was finished. We found worn suspension components, replaced them, rechecked the leveling and tested a spin cycle. It ran quietly again. The full story is on our noisy washer page.

What does a shaking washer repair cost?

The service call is $75. Leveling and load advice cost nothing extra if that is the fix. Suspension parts mean a written price before we begin. See the cost guide.

Why a washer shakes or walks

Spin speed multiplies any imbalance. A washer that sits slightly off level or holds a lopsided load can start shaking hard enough to move across the floor. Shaking has three families of causes: the load, the installation, and worn parts that are meant to absorb vibration.

Load causes

Heavy, absorbent single items such as a bath rug, a jacket or a pair of jeans can bunch against one side of the drum. Most washers sense this and re-balance, and when they cannot, they repeat the spin or stop. Wash these items with a few smaller ones, and avoid running a single bulky item by itself.

Installation causes

  • Not level. Adjust the front feet until a level reads flat in both directions, then tighten the lock nuts. Our guide to leveling a washing machine walks through it.
  • Soft floors. Older Mississippi homes with wood-framed floors can flex under a spinning washer. A solid, level platform or a plywood pad under the feet can help.
  • Shipping bolts still in place. A new or moved front-load washer with its transit bolts installed will shake violently.
  • Hoses and drain line. A stiff hose pressed against a wall can transmit vibration.

Worn parts that cause shaking

Top-load washers hang the tub on suspension rods, and front-load washers use shock absorbers or dampers and springs. When they wear, the tub bounces and bangs. A technician can check them by pushing the tub and watching how it settles. A worn bearing can also cause shaking along with a rumbling noise.

CheckWhat good looks like
FeetAll four firm on the floor, no rocking corner to corner
LevelFlat front to back and side to side
LoadNo single heavy item; drum about three quarters full
Tub movementSettles quickly when pushed, no knocking

When to call

If the washer is level, the load is balanced and it still shakes or knocks, the suspension, dampers or bearing are the likely cause. These repairs vary a lot by model and age, so we diagnose first and give a written price before starting.

Related problems

If the shaking comes with a loud bang or grind, read noisy washer. For spin trouble, see washer won’t spin.

FAQ

Shaking washer questions, answered

Why does my washer shake violently on spin?

It is usually an unbalanced load, an unlevel washer or worn suspension. On a new washer, shipping bolts left in place cause violent shaking.

How do I level my washer?

Push on each top corner to find the one that rocks. Turn that foot until the washer sits firmly, then tighten the lock nut against the base. Check again with a spin.

Can a washer shake because of the floor?

Yes. A soft, bouncy or uneven floor can make even a level washer shake. Moving it to a firm spot or reinforcing the floor helps.

Is it safe to keep using a washer that walks?

A small amount is common, but a washer that moves a lot can pull its hoses loose and damage floors. Fix the cause before it gets worse.

Can you replace washer suspension in Hattiesburg?

Yes. We inspect the suspension, replace worn parts, level the washer and test a spin cycle before we leave.

Washer shaking? We’ll steady it.

Call (601) 419-6599 for a written price before any work starts. 2624 Lincoln Rd, Hattiesburg, MS 39402. Monday to Saturday, 8 a.m. to 6 p.m. Request service for washer shaking and walking today.