How to Level a Washing Machine

A level washer is quieter, shakes less and lasts longer. Here is how to get all four feet firm.

Short answer

To level a washer, push down on each top corner to find the one that rocks, turn that foot until the washer sits firmly, tighten the lock nut against the base and check again with a spin. Use a level on top. If it still shakes, the floor, load or suspension may be the cause.

Why does leveling matter?

During the spin, an unlevel washer rocks and bangs. That wears the suspension, bearings and floor. Leveling is free and fixes a lot of noise and shaking.

How do I level it?

  1. Put a small level on top of the washer, front to back and side to side.
  2. Push down on each top corner and see which one rocks.
  3. Turn that foot by hand or with a wrench until the washer is firm.
  4. Tighten the lock nut up against the base so the foot stays put.
  5. Check again with a level and push on each corner.
  6. Run a spin with a small load and watch.

What if the floor is the problem?

Older Hattiesburg homes and pier-and-beam floors can flex, and vinyl over a worn slab can be uneven. A washer on a soft floor may shake even when level. Move it to a firm spot or ask a contractor to reinforce the floor.

Why levelling matters

A spinning washer drum can reach high speeds with a heavy, wet load. If the machine is not level, the vibration grows with every rotation and the washer starts to bang, shake and walk. Levelling also protects the bearing and suspension from extra stress, and it prevents many “unbalanced load” stops and error codes.

What you need

  • A small level, or a level app on a phone laid flat on the washer’s top
  • An adjustable wrench or pliers for the lock nuts on the feet
  • A helper if the washer is heavy

Step by step

  1. Move the washer into position with all four feet on a solid, flat part of the floor.
  2. Place the level on top of the washer, front to back, then side to side.
  3. Adjust the front feet by turning them: clockwise lowers the washer, counterclockwise raises it. Most washers only adjust the front feet, and the rear ones are fixed or self-adjusting.
  4. Tighten the lock nut on each adjusted foot firmly against the washer’s frame so it cannot drift.
  5. Do the rock test: press down on each top corner. The washer should not rock or shift diagonally. If it does, adjust again.
  6. Run a spin cycle with a medium load and watch for shaking.

Common problems

ProblemFix
Washer rocks corner to cornerOne foot is too high; lower it until it touches firmly
Floor flexes under the washerUse a solid platform or ask a contractor to stiffen the floor
New front-load shakes hardCheck that shipping bolts were removed from the back
Feet slip on smooth floorsAdd anti-vibration pads under the feet

When levelling is not the answer

If the washer is level and balanced loads still make it bang, the suspension, dampers or bearing may be worn. See vibration problems for the full diagnosis.

How to check that a floor is the problem

Stand next to the washer during a spin cycle. If you feel the floor bounce, the structure is flexing. In older homes with wood floors, a washer on the second floor or over a crawlspace can vibrate more than the same washer on a concrete slab. Placing the washer near a wall, where the joists are strongest, and using a solid pad often helps.

What good installation looks like

  • The washer is level in both directions and does not rock.
  • Hoses are not kinked and the drain hose is secured, with a loop at the top to stop siphoning.
  • There is a few inches of space behind and beside the washer for airflow and hoses.

When is it not a leveling issue?

If the washer shakes with a small load on a level floor, the suspension may be worn. See vibration problems and noisy washer.

FAQ

How to level a washing machine questions, answered

How do I know if my washer is level?

Place a level on top and push each corner. It should not rock.

Do I need special tools?

A level and, sometimes, a wrench for the lock nuts.

Why does my washer still shake after leveling?

An unbalanced load, a soft floor or worn suspension may be the cause.

Should I put pads under the washer?

Anti-vibration pads can help, but level it first.

Can you fix a washer that keeps walking?

Yes. We check the suspension and level it on a visit.

Washer still shaking? We’ll check it.

Call (601) 419-6599 for a written price before any work starts. 2624 Lincoln Rd, Hattiesburg, MS 39402. Monday to Saturday, 8 a.m. to 6 p.m. Request service for how to level a washing machine today.